Year-round lushness, savings on water, little maintenance, a surface that is perfect for both kids and pets; these are among some of the benefits every homeowner stands to enjoy with an artificial grass installation. As a homeowner, you can choose to either engage the services of a professional installation, or have a go at it yourself as a DIY project.

Perth Artificial Grass supplies top quality wholesale synthetic grass to homeowners who wish to undertake a DIY artificial grass installation, at the most competitive market prices. Not only that, but through collaborative effort, the installation team has prepared a step-by-step installation guide that will help every DIY enthusiast with the artificial installation process. The guide also includes a comprehensive list of supplies and tools needed for the job.

Must-Haves for the Job

It has been said that being thoroughly equipped for a job equates to being halfway done with job itself. And that is exactly just how crucial getting the right tools and supplies is to your DIY artificial grass project. As such, before starting out on your project, here is a list of the tools and supplies that you will need to secure

  • Measure of artificial grass as required
  • Tape measure
  • Road base such as crushed rocks
  • Little water
  • Rake and shovel
  • Compactor
  • Very sharp knife
  • Synthetic turf joining tape
  • Hammer
  • 100 mm flathead nails or ground pins
  • Steady and reliable power outlet
  • Power broom or a stiff-bristled broom
  • Whitewash sand
  • Power blower

Removing Existing Turf

The very first thing to do is to remove all existing turf from your choice of a site for the installation. A simple gardening tool such as a spade would suffice for the job. Using a spade for a large area will definitely prove tedious; in which case you are better off using a turf cutter. Dig out to a depth of between 70-100 mm.

A Base for the Installation

For a base, you can choose to have crushed rocks or an aggregate of the crushed rocks and sand.  Spread the base for your installation site using a rake. For the best results, sprinkle some water over this spread before compacting.  For compacting, you can use a builder’s plank or a power compactor.  At the end of this step, you should have an evenly flat and hard base.

Laying the Artificial Grass

After a careful preparation of the site, the next step is the actual laying of the grass.  For this it is important to ensure that you carefully measure the artificial grass you will need for the area. With a tape measure in hand and a sharp knife you can cut pieces that approximately fit within the edges selected. Use the sharp knife in clean cutting strokes to trim the edges accordingly. Also ensure that each roll is laid out in the same direction as tis will make the final layout even more attractive and even.

Having patches all around would not do for a beautiful finish. That is not to mention the fact that the pieces will be moving around so much and so many undesirable materials can easily get  in between the pieces.   That is why you will need to join the different pieces for an attractive spread.  For this task, you will use the synthetic turf joining tape; being careful to ensure that no pieces overlap at the joint and that no artificial grass fibers get entangled in the tape.

Your choice of artificial grass will greatly influence your experience of this step. Perth Artificial Grass products are designed for easy installation, rolling out quite easily and without creasing. We are the supplier of choice for artificial grass installation DIY enthusiasts like you from across the region.

Holding Down the Grass

Being subjected to any form of traffic will definitely make your synthetic turf move around in its place. This is very undesirable and what you can do to avoid this eventuality is to secure or hold down the artificial grass firmly onto the base.  You can choose to use ground pins or hammer down  flathead nails at regular intervals along the edges. The recommended interval is at about every 150-400 mm.

Adding Sand as an Infill

Adding sand infill has so many benefits for your DIY artificial grass installation. Spread the recommended   10-15 Kgs per square metre of your new artificial grass lawn and enjoy the benefits, These include a more solid feel on the underfoot as you walk around as well as superior drainage performance.  The sand also gets in between the synthetic grass blades, helping the artificial turf remain erect at all times, regardless of the pile height.

For better results, you can always use a blower to spread the sand even more evenly on the synthetic turf.

A Partner for All Seasons

Creative genius has seen to an unprecedented soar in the diverse applications of artificial grass. No longer is synthetic turf just for lawns and sporting fields; today, it has found application in interior décor and pet runs among many other applications.

Perth Artificial Grass provides our customers with a wide range of grasses for the different applications. The resourceful DIY artificial grass installation guide is a brain child of our expertly trained and experienced installation team and is perfect for homeowners looking to install synthetic turf out back or on their front yards.

Our team is always ready to assist accordingly for any other type of installation on other surfaces such as concrete, wood and stone for walls, patios and decks, rooftop gardens, swimming pool surrounds among many others.

Do not hesitate to get in touch today, even as we look forward to hearing from you.

Feedback

Did you find this guide resourceful? Have you any thoughts on how to make it better? Perth Artificial Grass is about more than just providing technical support through our multi-talented teams, we are always happy to hear some feedback from all our DIY clients , which will help us provide the best experience for everyone.

Perth Artificial Grass is more than happy to help you out with any questions.
Below is our contact details, so feel free to send us an email whether it be about a job or you just need some advice on how something should be done the right way.

Showroom: 2/18 Tacoma Circuit, Canning Vale

 Perth, Western Australia
6155 Australia
Phone: 0411 861 971
Email: [email protected]